Magnetic wand Features

magnetic rods work environment determines that it must have a certain degree of corrosion resistance, high temperature properties, and some situations require a relatively strong magnetization. By using different thicknesses of magnetic sheets can be different magnetic flux density. Select a different magnet bars can determine the maximum magnetic flux density and temperature resistance, usually in order to achieve on a conventional ∮25 10,000 gauss magnetic wand over the surface of the magnetic flux density requires a high-performance model of NdFeB magnets. High temperature magnetic rods in temperatures over 150 degrees or more general choice of SmCo magnet.

Wear-resistant ceramic patch use

An essential part of the wear-resistant ceramic chip instead of the magnetic separator, only the customers need for magnetic separator drum surface abrasion treatment, extended magnetic drum (outer protective seal cylinder) case of the use of time will be a patch ; during roughing, the case of mineral particles of magnetic separator is likely to cause more appropriate to wear the patch installed; tank inside another wet drum separator can also be installed abrasion resistant ceramic chip.

Cross-belt magnetic separator features

recycling cross belt magnetic separator  features is the magnetic system for the electromagnetic system and a large wrap angle magnetic system for 270 °. In order to improve the thermal and moisture by preventing the coil, the inner cylinder is filled with transformer oil; drum speed is slower, 5 revolutions per minute, the belt around the cylinder to slow motion, magnetic products are discharged by a belt excellent dehydration (magnetic product concentration up to 65% -70%), cross belt magnetic separator for heavy media recovery and reuse is very important.

Advantages cross belt magnetic separator

recycling cross belt magnetic separator is transportation, screening, mineral processing equipment integrated, cross belt magnetic separator  with high dressing efficiency advantage. Belt magnetic separator machine suction side installation, pick up chunks of iron pieces selected rate. The unique design of the stainless steel liner as a protective layer, compared with the traditional belt separator can more effectively reduce their sharp ferromagnetic material damage, extend the life of the device for reliable operation, little maintenance, greatly reducing operating costs .

Structure Magnetic Separator

magnetic separator is mainly composed of a cylinder, magnetic system, tank, transmission parts in four parts. Cylinders made of stainless steel plate 2-3mm welded into a tube, cover the cast aluminum parts, connected by stainless steel screws and cylinder motor by deceleration machine, driven cylindrical rotary movement. magnetic system for the open magnetic system, mounted in the cylinder. magnetic blocks with stainless steel bolts mounted on the yoke plate, extending cylinder axis of the yoke, the shaft is fixed Abduction arm pulling the crank arm can adjust the angle of the magnetic system, the lever can be adjusted suitable fixed working area with other parts of the tank stainless steel plate, frame and tank with ordinary steel welding.
According to different structure type tank, dry magnetic separators is divided into downstream, counter-style, semi-countercurrent three.

easy to operate, easy to maintain.

magnetic separator is suitable for wet magnetic separation granularity below 3mm magnetite, pyrrhotite, roasted ore, ilmenite and other materials, also used in addition to iron work coal, non-metallic minerals, building materials and other materials. Magnetic separator magnetic system, using high-quality ferrite material or rare earth magnets composite, high average magnetic induction tube table. According to user needs, we can provide a variety of different table strong magnetic downstream, semi-countercurrent, countercurrent type.It has a simple structure, large capacity, easy to operate, easy to maintain.

Caution Magnetic Separator

Caution magnetic separator
(A) Before use, the transmission should be added to an appropriate amount of gear oil, lubricating all the bearings.
(B) When using a magnetic system angle adjustment: that means pulling the magnetic system to adjust the high-side edge of the magnetic system to adjust to higher level trough unloading at the mine mouth.
(C) before driving should be careful to check the power lines around the gear, lubrication systems, equipment cases, confirmed normal, open the device ministries pipes, then to mine. Stop should be the first stop to the mining, gradually close the water gate. ;
(D); best choice of size of aircraft do not ask for the 60-80 mesh, the lower limit of the effective recovery of sludge is 40 microns.
(E) to determine the size of the ore concentration ore slurry flow rate of a certain amount of time to affect the size of the sorting. High concentration, slow flow, resistance, easily mixed with gangue concentrate, reduce concentrate taste, but because of the long time dressing, beneficial for recovery; the other hand, if low mineral concentration, the concentrate may be higher taste, while tailings taste It will be increased, so that the recovery rate is reduced. Reasonable feed concentration of 25-35%.
(F) a reasonable adjustment to the break up of water and concentrate ore flushing water. Break up too much water, slurry flow rate is too fast, the taste will tailings increased. Conversely, break up small water, mineral particles will not sufficiently loose and affect the separation efficiency, reduce tailings taste. Concentrate rinse water is mainly used for removing the concentrate from the drum skin, rinse water drop size should be able to ensure concentrate discharge it.
(G), please pay attention to protection.
(H) the user maintenance coolant magnetic separators process, should be strictly controlled technical indicators and work space, so as not to affect the sorting effect.